How to sew skirts – FREE DIY SKIRT PATTERNS

• The names of skirt variations

Don’t forget to checkout if that skirt will suit your bodyshape or not and the different silhouettes you can design for your skirts.

To draft a pattern for skirts, the basic measurement you need are –

• • Waist round (You can add 1 inch or 3 cms to waist circumference for ease)

• • Hip round (You can add 1-2 inches or 3-5 cms to hip circumference for ease)

• • Length of the skirt ( Take differently for back and front if you have a pear-shaped body and the hips or bottom is prominent. The length of the skirt will fall differently if the same length is taken for front and back.) The length of the skirt is preferable. A 30-inch or 70-cm length is the average length for a skirt.

• • The flare of the skirt – this can be calculated as an angle. A 20degree flare can give you a normal flare, a 60°can give you a flared skirt).

• • Distance from the waist to the hip.

Learn how to make a skirt block pattern with this tutorial

Checkout this post on the different waistbands available for you.

Learn about how to sew the straight waistband of a skirt here.

Or other ways to sew the waist  – like a waist finish for skirts with zipper here.

Here is a tutorial to Make a Pull down half circle skirt  

Learn how to sew zipper on a skirt

Make the most basic tailored waistband with a classic skirt.

Or a plain skirt with a flounce hem.

Or this detailed tutorial for a simple  straight skirt with yoke and zippered opening.

Or make this simple gathered skirt with a fitting waistband – a dirndl skirt.

This skirt tutorial is to sew a long full skirt without much fabric.

Checkout the post on hemlines and skirt lengths : 9 important names .

Related posts :

A line skirt pattern.

A Reversible full skirt pattern.

Sewing tutorial for a Lolita skirt

        

  

  

[toc]

Opening

In a skirt, usually, the opening is kept on the side seams, though center-back openings are also common. Center-front openings are also used, though rarely.

Hems

The hem is usually a turned under edge – a 2 1/2 inch extra is added to the bottom edge for this turned under hem.

Pockets

Side seam pockets are the most commonly used pockets for skirts. Patch pockets are also used.

Waistbands

Usually, a waistband of 1 1/2 to 2 inches is given to skirts. The width will be the waist round ( measure around where you will tie the skirt without any belt) plus 1 inch extra. If there is an extension for a stud or buckle, add 1/2 inch extra.

Trims

You can add frills, lace, ribbon, etc., as trims to give an extra edge. You can add a sash and tie a bow on the front for a cute look.

Straight skirt

Skirts are one of the easiest clothes you can make for yourself. Out of that, a straight skirt is the easiest. 

Measurements you need to make a pattern for a simple straight skirt block.

• Waist round (Where you mean to tie the skirt).

• • Hip round ( The widest part of hip).

• • Measure distance from waist to hips ( Mostly, this is 7 inches; better measure on your own body. Check out this post on body measurements for more details).

• • Length of the skirt, from the waist.

You can make a simple straight skirt with a zipper opening from these measurements. This skirt is better made below knee. If you are making it over the knee, you may need slits for walking ease as in the case of a pencil skirt.

Check out these posts on how to go about making sewing patterns and how to cut fabric for more details.

FRONT SKIRT BLOCK

A-D = 1/4 of hip round
A-C = 1/4 of waist round + 1/4 inch ease + 2 inch or so ease
A-B = 1/2″
A-H = 7″
I-J = 1 1/2″
C-N2 = 2″
N1-N2= 3/4″
M2-N2 = 1 1/2″
M1-M2 = 3/4″
N-P= 3″
M-O= 2.5″

BACK SKIRT BLOCK

A-D = 1/4 of hip round +1/2″
A-C = 1/4 of waist round + 1.5″
A-B = 3/4″
A-H = 7″
I-J = 2″
K1-K2= 1.5″

Add your waistband. A straight waistband with a buckle or a faced one will work. 

A line skirt

This skirt has the shape of alphabet A, tight at the waist and hips and flared at the hem. This classic skirt is a favorite of all those who wear skirts, as it is flattering to most body shapes.

 How to make an Aline skirt pattern

Cut a Front Pattern for Aline skirt

A- B= Length of skirt needed +1/2 “

A-C = 3/4 inch

A- D = 1/4 of waist round + 1/2 inch ease+ 1/2 inch seam allowance

A- F = 8″

F-H = 1/4 of Hip round + 1/2 inch ease+ 1/2 inch seam allowance

G-I = 3″

K-G – 1″

The A line skirt can have a minimum flare of 1 inch more than your hip round and maximum flare of 3-4  inches more than 1/4 of your hip round.

Cut a Back pattern for an Aline skirt

A- B= Length of skirt needed +1/2 “

A-C = 3/4 inch

A- D = 1/4 of Waist round + 3″

A- F = 8″

F-H = 1/4 of Hip round + 1/2 inch ease+ 1/2 inch seam allowance

G-I = 3″

K-G – 1″

Darts in the back pattern

Divide C-D into 3 equal parts and mark M & L as dart points

Dart width – 1 inch for each dart; i.e., mark 1/2 inch on either side of the darts..

Dart length – 4 inches; join the dart line.

For side opening, mark 1/6th of waist from F ; For zipper opening – 7.5 inches.

Either draft a waist band, or make facings with the same pattern copying the pattern for front and back patterns to a width of 3 -4 inches.

freeimages.com/Lotus Head

Gathered skirt

A simple construction, this skirt gathers at the waist.

You need a rectangular fabric piece, the width of which is three times your waist round and the length, however long you want the skirt to be. You can tweak the measurement as you like it- if you wish to have lesser gathers or have only so much fabric, you can reduce the width accordingly.

Make a waistband for your skirt with elastic inserted, and you are done. You can convert the top portion of the skirt piece into an elastic waistband also.

Circle skirts

Circle skirts look wonderful on all girls, big and small; the way they move around the body is beautiful and very flattering; but their construction is not as easy as it looks.

Most of the circle skirts we see are full circle skirts without a seam and they need a very wide fabric to accommodate the pattern. Variations include half and three-fourth circle skirts.

This skirt is cut on a bias grain of the fabric, tight at the waist, and flared at the lower edge.

Now consider the fabric you have – if you have a very wide piece of fabric, you can get a full circle, but this is very rare. (Checkout the post on fabric measurements) .

But if you have a narrow piece of fabric, you will have to make do with joining 1/4 circles. The number of 1/4 or 1/2 circles you want will also depend on your fullness.

3 1/4 circles or three half circles are the commonly used dimensions for circle skirts though six half circles are also used for a full skirt.

Let us see measurements for 1/4 circles or 1/2 circles you will need.

Measurements you need to sew the skirt

• Length of the skirt

• • Hip round

Add 4″ to the length needed for waistband seam allowance and hem seam+ some inches for shifting ( 5-6 inches if you are making a very long skirt)

Length of the skirt fabric = Length you need + 4″ + 5″
A=length you have calculated

B= Hip measurement divided by No of 1/4 or 1/2 circles in the skirt + 2″
c = hip measurement divided by no of 1/4 circles in skirt * 2″ divided by 3.14

If you are not sure about how much fabric is needed to sew the circle skirts, consider this.
For one 1/2 circle skirt piece, the width of the fabric should equal A+C, and the length of the fabric should be (A+C)* 2. The total length needed will be (A+C)* 2 * no of 1/2 circle skirt pieces you will be joining in making the skirt.
For a 1/4 circle skirt piece, the width of the fabric should be equal to A + C and the Length also should be equal to A=C.

Tips for stitching circle skirts

Hem – One tough thing for most people in making a circle skirt is a neat hem that is not twisted. The circular shape of the bottom edge of the skirt makes it very difficult to hem. Hand hemming will take a lot of time. I turn 1/4 inch inside and edge stitch once all around the hem.

Cut away extra fabric close to the stitch line (time-consuming but very well worth the time spent for a neat-looking hem). Now turn the edge inside once more and edge stitch.  

Another tip is to choose a pattern with elastic in the waist rather than one with a zipper – then the sewing of a circle skirt will seem easier.  

Checkout the post on 16 Ultimate circle skirt patterns from around the world.

Related posts

Handkerchief skirt

The edge of a handkerchief skirt dips down to a point and hangs down like the tip of a handkerchief.

This skirt basically is a square fabric with a waistband and its hem falls down like the corners of a handkerchief, hence the name handkerchief skirt. More and more layers of fabric can be used to increase the visual effect of the number of pointed hems.

As this skirt has an asymmetrical hemline, this skirt can be said to be flattering to all, especially short girls. The result is you can look taller if you don this skirt. Ahhh, A DIY handkerchief skirt is what I needed to look tall all this time. 

You need at least 2 1/4 meters of a 45 inches wide cloth to make this skirt with two layers for an adult. The width of the cloth determines the length of your skirt, so the wider the cloth you have, the longer your skirt will be. The length of one side of this square is double the length of your skirt.

Divide the cloth you have into two squares of equal size.
Hem all four sides of the squares – you can decorate the hem with ribbons poms-poms, tassels etc.

Measure hip round loosely.

Divide the hip measurement by 6.28 – this will give you the radius of the circle you will have to cut out from the center of the squares

Fold the cloth along the middle first 1-2 ; then along 3-4 as per the diagram – you will get a square shape as the second diagram.

A-B = A-C = Radius of the circle you get by dividing your hip round by 6.28. Cut out the portion outside of B-C in a curved line making sure all the points are equal to the radius.

Line up the square fabric bottom layer right side up on top of the Top layer right side up. Pin along the circular hole in the middle aligning both the cloth.

Stitch around the circle edge twice with a 1/4 inch seam allowance.

Pull down the bottom layer to the back through the center hole.

Now the skirt portion is ready; you can assemble the whole handkerchief skirt by attaching a fabric waistband casing with elastic or a matching elastic waistband directly stitched to the skirt.

Make sure to take elastic 1 inch lesser than your waist measurement for a snug fit.

Gored skirt

How to make a 6 panel gored skirt

A gored skirt is a paneled skirt with 3 panels in the front and three panels in the back. All the panels will be of similar size. 

A-B = 1 inch

C-D = 1 inch

B-E = Full length needed +1.5 inch seam allowance minus waistband width.

Mark these on both sides of the pattern as shown in the diagram.

Join E- D and B- C in a soft curved line.

From one piece of cloth cut 2 pieces of panels.

Cut 4 more  for gored skirt pattern pieces.

Novelty gathered (Tiered skirt )

This skirt consists of three tiers of fabric attached to each other. Each tier is attached to the other one with lots of gathers.

The 3 tiered panels of the skirt should be cut as detailed in the diagram.

All the tiers are of the same length; the addition of  2.5 inches in the 1st tier is for the waistband  2 inches and the bottom edge seam allowance 1/2 inch.

The 2nd tier has 1/2 inch each seam allowance for upper edge and bottom edge.

The 3rd tier should have a seam allowance of 1/2 inch for the top edge and hem turning of 1 inch.

The waist band of this skirt should have elastic inserted – cut elastic 1 inch smaller than the waist round. 

Join the short edges of all panels to make 3 round tiers. 

Gather the top edges of 2nd and third tiers to match the top edges of 1st and 2nd tiers, respectively. Join all the tiers, and voila, the skirt is ready.  

Checkout this tutorial to sew a tiered skirt.

freeimages.com/ alexander redmon

Tulip hemmed skirt

This is a skirt devoid of a side seam, and one part of it overlaps the other. It is usually worn over tights by ballet dancers.

How to make a wrap around Tulip hemmed skirt Pattern

You need an Aline skirt pattern to make this skirt; As this skirt comes without side seams, the back pattern and front patterns have to be joined after altering the front pattern.

From the center line of the front pattern of Aline skirt mark 5 inches . Draw a curved line from the bottom center line to the marked point as in the diagram below- make a similar mirror pattern to the other side also.


Cut out the two front panel patterns outside the curved lines; Join them to the back pattern of an A-line skirt.

Waistband
You need a waistband which will wrap around your body – you can make this out of the same fabric or a ribbon of 1″ width.

Measure the total width of the skirt waist. Add a 1-inch seam allowance. Add 40 inch extra.

Sew a buttonhole in the waist band of the front flap to insert the tie.

Pleated skirt

A pleated skirt has pleats made by machines or by hand that adds fullness, grace, and beauty.

How to make a pleated skirt pattern 

A-H = Total width of cloth taken divided by 4 + 1″ seam allowance = H-I.

H-F = 1 3/4″
A-B = 1 1/4″

B-C = Length needed – Waistband width (1″) + 1/4″ seam allowance
Mark F-E same as B-C.

F-G ( side opening) = 1/6 waist or 7.5 if using zipper.

How to make pleats

Width of pleats =  { (B-F – (minus)  1/4 waist ) + 1/2 } divided by 2

 

( Checkout the post on 5 beautiful pleats you could sew on your clothes )

photo: free images.com/Marília Florêncio Santos

Layered skirt

This skirt may be gathered or circle skirts but consists of two or more layers.

Another way of making it is to layer it with ruffles.

To make a ruffled skirt with layers, you need six pieces of fabric cut per the diagram below. The first connecting piece will be used as a waistband inserting elastic cut the same size as the waist round or slightly smaller.  

Waistband 

How to draft waist band for your skirt

If using interfacing ( highly recommended to use ) cut it to a width of 1 inch and length of waist round + 2″ overlap (without seam allowance)

Related posts