How to make BIAS BINDING TAPE – 3 best ways

More like this:

• Different types of bias tapes
• What is bias cut
• How to do bias binding –  best methods
• How to bind neckline with bias tape

3 Different types of bias tape you can make

There are three main types of bias tape as I understand it – Single bias tape, single fold bias tape and double fold bias tape. (You may find different versions of the same thing with different names elsewhere – but basically, they are the same).

Single bias tape

Usually measures 1/2″ when finished. A wider single fold bias tape can measure 7/8″

A single-fold bias tape is a strip of bias-cut fabric that is folded in the center and pressed. I use this for binding the armholes. The edges of the bias tape are stitched to the edge of the garment and turned to the wrong side. It is then stitched into the ditch or hand-stitched there.  

Single Fold bias tape

Single-fold bias tape has both raw edges folded inside. It has a single fold running along each long edge of the tape.

In general, single-fold bias tape is used to finish the neckline and armhole edges when the tape will be stitched in place, (RIGHT SIDES together) and then turned to the inside of the garment and stitched in place again.

The tape never shows on the garment’s outside (RIGHT SIDE). 1/2 inch and 1″ are most commonly available in stores. It is also used to make casings.

Double-fold bias tape 

Double-folded bias tape can measure 1/2 inch or 1/4 inch when finished. 

The 1/4 inch double bias tape is basically a single fold bias tape with a fold in the center.

It has the same two folds along the long edges as a single fold, but the double-fold tape has an additional fold slightly off-center, making one side a little wider than the other.

The double-fold bias tape fabric is cut 4 times as wide as the finished bias tape you want. So if you want a 1/4-inch bias tape, you must cut a 1-inch fabric strip. If you want a 1/2 inch bias tape, cut a 2-inch fabric strip; for 1 inch finished bias tape, cut a 4-inch wide fabric piece.

Double-fold bias tape is often used to encase a raw edge. In this case, the tape will show when the garment is finished. You can also use it as a spaghetti strap or drawstring cord.

Double folded blanket binding is used to bind blankets, quilts etc.

Making Bias tape

Getting those pre-packaged pre-cut bias strips in different colors is very convenient if you are short of time. But it is very easy to make bias-binding tapes. There is something therapeutic about making those beautiful tapes, and so cheap to make from leftovers from sewing projects. It sometimes gets difficult to get those ready-made bias tapes in the same color or pattern you want. All these are the reasons why people passionate about sewing always make them whenever they get a chance.

[toc]

Cut short length bias-binding tape

The easy way to make short-length bias tapes is to find the 45 angle across the fabric surface. Mark the diagonal line.

Mark adjacent parallel lines for the width of the bias strip you want. Cut along the marked lines.

Now, join them together to make the long bias tapes –

• • Place the first strip face up on the table.

• • Place the 2nd strip face down on the table on top of the first, so it is at a 90-degree angle.

• • The resulting two strips should make an L shape. Ie. Keep the strips’ right sides across each other, extending at the edges.

• • Draw a line with a pencil between the two points where the two strips cross.

• • Then sew on this line. Join them together diagonally, as in the picture.

Cut bias tape from fabric squares

You can cut these bias tapes from square fabrics. Here is a chart showing dimension of the square fabric that is needed to cut to make a 60 inch long bias tape.

Here is a chart showing dimension of the square fabric that is needed to cut to make a 100 inch long bias tape.

Make Continuous bias-binding tape

This is a very easy to make long long bias tape. No more cutting and joining; the joining is done first and then the tape is cut.

A continuous bias tape is a very easy-to-make long, long bias tape.
No more cutting and joining; the joining is done first, and then the tape is cut.

Excellent when you have spare time, and you got this small square piece of fabric you think will make excellent piping for a future skirt or something.

Yes, a square is all you need to make all those lengths of tape. You will have to decide on how long you want the tape and what is the width of the tape. Calculate the size of the square and go about cutting them.

How to calculate the size of the square if you know the length of bias tape you need

It is simple enough. You just multiply the bias tape length and the width of the fully opened tape. Just find the square root of this, which gives you the size of the side of your square.

If you want 2 meters ( 200 cms)of bias strip needed, how to calculate the size of the square you should cut it from

so 200 * 1-inch bias strip = 200 ( area of the bias tape)
you have to find the square root of this area to find the size of the square. Easy. So the square root of 200 = 14 cm square piece will yield you 2 meters of binding tape.

Step 1

Take the square piece of fabric. Cut it into two pieces by diagonally cutting it. You have two triangles now. 

Step 2

Join them by short sides ( not the diagonal sides)

Step 3

Open it up and press the seam allowance open. Mark the bias strips all along the width.

Step 4

Now join the short sides , right sides together. One end would not meet but that is ok.

Step 5

Start cutting the bias tape strips from one end ( the extended, not stitched end). Go on cutting until the end and get this long strip of bias binding tape.  

Make long  bias binding tapes from one small and long fabric piece

This method is complicated, and I much prefer the second method to make a long binding tape. But if I do not have a square piece of fabric, I work with what I have and get those long strips.

Checkout the video for more details . 

Make bias tape with a bias tape maker

You can buy small simple handy bias making tools or an electric bias tape maker instead of going into all these trouble. Check out this post on using bias maker tools here.

Related posts: How to sew binding on necklines; Using a binding presser foot; Sewing tutorial for making mitered corners with binding and otherwise.